BAILII is celebrating 24 years of free online access to the law! Would you consider making a contribution?
No donation is too small. If every visitor before 31 December gives just £1, it will have a significant impact on BAILII's ability to continue providing free access to the law.
Thank you very much for your support!
 |
[Home] [Databases] [World Law] [Multidatabase Search] [Help] [Feedback] | |
United Kingdom Statutory Instruments |
||
|
You are here: BAILII >> Databases >> United Kingdom Statutory Instruments >> The Motor Vehicles (Type Approval) Regulations 1980 No. 1182 URL: http://www.bailii.org/uk/legis/num_reg/1980/uksi_19801182_en.html |
||
[New search] [Help]
Statutory Instruments
ROAD TRAFFIC
Made
6th August 1980
Laid before Parliament
19th August 1980
Coming into Operation
9th September 1980
The Minister of Transport, being a Minister designated(1) for the purposes of section 2(2) of the European Communities Act 1972 in relation to the regulation of the type, description, construction or equipment of vehicles, and of components of vehicles, and in particular any vehicle type approval scheme, in exercise of the powers conferred on him by the said section 2(2) and of all other enabling powers, hereby makes the following Regulations:-
1. These Regulations shall come into operation on 9th September 1980 and may be cited as the Motor Vehicles (Type Approval) Regulations 1980.
2. The Regulations specified in Schedule 3 are hereby revoked.
3.-(1) In these Regulations-
"certificate of conformity",
"component",
"conform" means
"information document" means
in relation to an application, not being an application within sub-paragraph (iii) below, for the approval of a motor vehicle to which these Regulations apply, a document in the form set out in Part I of Schedule 1,
in relation to an application, not being an application within sub-paragraph (iii) below, for the approval of a trailer to which these Regulations apply, a document in the form set out in Part II of Schedule 1,
in relation to an application for the approval of a vehicle to which these Regulations apply and for which the type approval requirements are contained in a single Community Directive or Regulation, or for the approval of a component of a vehicle to which these Regulations apply, a document in a form issued for the purpose of such application by or on behalf of the Minister;
"land tractor" means
"Member State" means
"road"
"the Community Directives" means
"the Community Regulations" means
"the Minister" means
"the relevant approval mark",
"the relevant aspects of design, construction, equipment and marking", in relation to a vehicle or to a component of a vehicle, means
"the type approval requirements",
"type approval certificate",
"vehicle component" means
references to the competent authority of any Member State other than the United Kingdom are references to the authority in that State which has functions in relation to the type approval of vehicles and their components corresponding to those of the Minister under these Regulations.
(2) Any notice required under these Regulations to be given by or to any person shall be given in writing.
(3) Unless the context otherwise requires, any reference in these Regulations to-
(a)a numbered Regulation or Schedule is a reference to the Regulation of or Schedule to these Regulations bearing that number;
(b)a numbered paragraph is a reference to the paragraph bearing that number in the Regulation or Schedule in which that reference appears.
4. These Regulations apply in relation to every motor vehicle (other than a land tractor) manufactured on or after 1st July 1973, being a vehicle which-
(a)has four or more wheels; and
(b)is so constructed as to be capable of exceeding a speed of 25 kilometres per hour on the level under its own power,
and to every trailer which is manufactured on or after that date, being a trailer drawn by such a motor vehicle.
5.-(1) Where the Minister is satisfied on an application made to him in accordance with Regulation 6 by or on behalf of the manufacturer of a motor vehicle to which these Regulations apply or of a vehicle component and after examination of the vehicle or, as the case may be, the vehicle component that-
(a)the vehicle or vehicle component conforms with-
(i)the information given in relation to the vehicle or vehicle component in the information document which accompanied the application, and
(ii)the type approval requirements; and
(b)adequate arrangements have been made to secure that other vehicles or other vehicle components purporting to conform with that vehicle or, as the case may be, that component in the relevant aspects of design, construction, equipment and marking will so conform in all respects or with such variations as are permitted by those requirements,
he shall approve the vehicle as a type vehicle or, as the case may be, the vehicle component as a type vehicle component and shall issue a type approval certificate in respect of it.
(2) A type approval certificate may be issued in respect of a type vehicle where the Minister is satisfied that one or more, but not all, of the type approval requirements are complied with in the case of that vehicle and a further type approval certificate may be issued by virtue of this paragraph on the application of any person who manufactures any part of the vehicle or by whom the vehicle is finally assembled, and references in these Regulations to a manufacturer shall be construed accordingly.
(3) Where the Minister, on such an application as is mentioned in paragraph (1), decides not to issue a type approval certificate in respect of a vehicle or vehicle component he shall give notice to the applicant of the decision stating the grounds on which it is based and informing the applicant of his right of appeal under Regulation 14 and, within one month from the date on which that notice is given, shall give the like notice to the competent authority of every other Member State.
(4) Where the Minister issues a type approval certificate in pursuance of such an application as is mentioned in paragraph (1) he shall, within one month from the date on which the certificate is issued, give notice of that fact to the competent authority of every other Member State and shall include with the notice a copy of the type approval certificate so issued.
6.-(1) An application by or on behalf of a manufacturer for the approval of a vehicle to which these Regulations apply as a type vehicle, or of a vehicle component as a type vehicle component, shall be made in writing to the Minister and shall be accompanied by an information document duly completed so as to furnish all the information required by the document (being such of that information as is applicable to a vehicle or, as the case may be, a vehicle component of the type in respect of which the application is made), together with such other documents as are mentioned in the said information document as being required in connection with the application.
(2) Where in pursuance of this Regulation an application has been made to the Minister in respect of a vehicle or vehicle component of a particular type, then until that application is disposed of or, where an appeal is made under Regulation 14 in respect of the decision on that application, until that appeal has been disposed of, no similar application in respect of a vehicle or vehicle component of that type shall be made by or on behalf of the same manufacturer to the competent authority of any other Member State.
7.-(1) Subject to paragraph (2), a manufacturer of a type vehicle in respect of which a type approval certificate is in force may issue, in respect of each vehicle which is manufactured by him and which conforms with the type vehicle in such of the relevant aspects of design, construction, equipment and marking as are mentioned in the type approval certificate, a certificate of conformity stating that the vehicle does so conform.
(2) Where a certificate of conformity is issued in consequence of any type approval certificate issued by virtue of Regulation 5(2), it shall relate only to the type approval requirement or requirements to which that type approval certificate relates.
8. A manufacturer of a type vehicle component in respect of which a type approval certificate is in force may mark each component which is manufactured by him and which conforms with the type vehicle component in such of the relevant aspects of design, construction, equipment and marking as are mentioned in the type approval certificate with the relevant approval mark.
9.-(1) A type approval certificate may be issued subject to conditions with respect to-
(a)the inspection by officers of the Minister of samples of vehicles or vehicle components purporting to conform with the type vehicle or, as the case may be, the type vehicle component in the relevant aspects of design, construction, equipment and marking and of the parts and equipment of any vehicles, and of the parts of any vehicle components, selected for such inspection, and, for that purpose, the entry of premises where any such vehicles or vehicle components are manufactured; and
(b)the notification by the manufacturer of differences of design, construction, equipment or marking (other than such variations as are permitted by the type approval requirements) between any such vehicles and the type vehicle or between any such vehicle components and the type vehicle component which might be relevant to those requirements.
(2) If it appears to the Minister that there has been a breach of condition subject to which a type approval certificate has been issued or if he ceases to be satisfied as to any other matter relevant to a type approval certificate, he may, by notice under Regulation 13, cancel or suspend the certificate.
10.-(1) Where a manufacturer of a type vehicle or a type vehicle component in respect of which a type approval certificate is in force-
(a)intends to cease the manufacture of vehicles or vehicle components conforming with that type, or
(b)intends to make any alteration in the manufacture of vehicles or vehicle components conforming with that type of a kind which would result in any of the particulars furnished in the relevant information document ceasing to apply, or
(c)intends to make any alteration in any of the relevant aspects of design, construction, equipment or marking (being aspects in relation to which notice has been previously given to the manufacturer by the Minister that they are aspects to which this sub-paragraph applies) of vehicles or vehicle components conforming with that type,
the manufacturer shall, as soon as practicable after forming that intention, give notice of it to the Minister specifying the type vehicle or, as the case may be, the type vehicle component to which it relates and-
(i)in a case mentioned in sub-paragraph (a) above, the date when the manufacture of the vehicles or vehicle components in question is to cease, and
(ii)in a case mentioned in sub-paragraph (b) or (c) above, particulars of the alterations in question and of the date or dates on which they are to be made.
In this paragraph the reference to the relevant information document is a reference to the information document which, in accordance with Regulation 6(1), accompanied the application under that Regulation for the type approval certificate in question.
(2) In addition to the notice required under paragraph (1) the manufacturer concerned shall, not later than fourteen days after the date on which he has ceased the manufacture of the vehicles or vehicle components in question or, as the case may be, after he has made any alterations such as are mentioned in paragraph (1)(b) or (c) give notice of that fact to the Minister specifying-
(i)the date (whether or not it is the same date specified in the notice under the said paragraph (1)) on which the manufacture ceased or, as the case may be, the alterations were made, and
(ii)where the notice under the said paragraph (1) related to a type vehicle, the frame or chassis number assigned to the vehicle of that type which was last manufactured before that date.
(3) A copy of any notice given by or to a manufacturer under paragraph (1) or by a manufacturer under paragraph (2) shall, within a period of one month from the date on which it is given, be sent by the Minister to the competent authority of every other Member State.
11.-(1) Where a notice given by a manufacturer under Regulation 10(1) or (2) is a notice that he intends to cease or, as the case may be, has ceased, the manufacture of vehicles or vehicle components of the type referred to in the notice, the Minister may by notice under Regulation 13 cancel the type approval certificate in force in respect of the type vehicle or, as the case may be, the type vehicle component to which the said notice relates.
(2) Where a notice given by a manufacturer under Regulation 10(1) or (2) is a notice that he intends to make or, as the case may be, that he has made alterations such as are mentioned in Regulation 10(1)(b) or (c) the Minister, if satisfied that the alterations specified in the notice are such as to make it appropriate to do so, may by notice under Regulation 13-
(a)cancel or suspend the type approval certificate in force in respect of the vehicle or vehicle component to which the notice relates; or
(b)cancel the said type approval certificate and substitute for it, without further application by the manufacturer, a new type approval certificate in respect of the vehicle or, as the case may be, the vehicle component; or
(c)modify the said type approval certificate.
12.-(1) If the Minister-
(a)after examination of at least two vehicles, being vehicles of a particular type in respect of which a type approval certificate is in force and in respect of each of which a certificate of conformity is in force, or after examination of at least two vehicle components, being components of a particular type which have been marked with an approval mark in accordance with Regulation 8 in respect of which a type approval certificate is in force, is satisfied that each of those vehicles or, as the case may be, each of those vehicle components has not been manufactured so as to conform with the relevant aspects of design, construction, equipment or marking; or
(b)is notified by the competent authority of any other Member State that, in relation to any such vehicles or vehicle components and the manufacturer thereof as may be specified by that authority, the authority, after such examination as aforesaid, is similarly so satisfied,
he shall give notice of that fact to the manufacturer specifying-
(i)the particular respects in which the vehicles or vehicle components in question have been found (either by the Minister, or as the case may be, the said competent authority) not so to conform,
(ii)the steps that shall be taken by the manufacturer to ensure that vehicles or vehicle components of that type are manufactured by him so as to conform with the said aspects and the period within which those steps shall be taken, and
(iii)that unless those steps are taken within that period the type approval certificate in question may be cancelled or suspended,
and if, at any time after the expiration of that period, the Minister (whether or not after any or any further examination of any such vehicles or vehicle components) is not satisfied that all the steps so specified have been taken, he may, by notice under Regulation 13, cancel or suspend the type approval certificate.
(2) A copy of any notice given to a manufacturer under paragraph (1) shall, within a period of one month from the date on which it is given, be sent by the Minister to the competent authority of every other Member State.
13.-(1) Where the Minister decides to cancel, suspend or modify a type approval certificate under any provisions of these Regulations, he shall-
(a)as soon as practicable, give notice of the decision to the manufacturer to whom the certificate was issued; and
(b)within one month from the date on which that notice is given, give the like notice to the competent authority of every other Member State.
(2) A notice under paragraph (1) shall specify the date on which the cancellation, suspension or modification of the certificate to which the notice relates shall take effect and shall specify-
(a)in the case of cancellation, the grounds for the decision to cancel;
(b)in the case of suspension-
(i)the grounds for the decision to suspend,
(ii)the conditions which must be fulfilled before the suspension can cease to have effect, and
(iii)that the suspension shall have effect until such time as the Minister gives notice to the manufacturer under this sub-paragraph that he is satisfied that the said conditions have been fulfilled; and
(c)in the case of modification, particulars of the modifications,
and shall inform the manufacturer concerned of his right of appeal under Regulation 14 in respect of the decision.
(3) The cancellation, suspension or modification of a type approval certificate under any provision of these Regulations shall not affect the validity of any certificate of conformity previously issued or any relevant approval mark applied in consequence of that type approval certificate.
14.-(1) A person who is aggrieved by a decision given by or on behalf of the Minister with respect to a type approval certificate may, within the time and in the manner respectively specified in paragraphs (2) and (3) appeal to the Minister, and on the appeal the Minister-
(a)shall have the like powers and duties as he has on an original application for a type approval certificate;
(b)may hold an inquiry in connection therewith; and
(c)may appoint an assessor for the purpose of assisting him in handling the appeal or any such inquiry.
(2) An appeal under paragraph (1) shall be made by notice to the Minister which shall be lodged with him not later than fourteen days from the date on which notice of the decision in respect of which the appeal is made was given.
(3) A notice of appeal under paragraph (1) shall state the grounds on which the appeal is made and shall be accompanied by the following documents:-
(a)a copy of the information document which, in accordance with Regulation 6(1), accompanied the application under that Regulation for the type approval certificate in question; and
(b)where the appeal relates to the cancellation, suspension or modification of a type approval certificate, a copy of that certificate.
15. The Minister may provide and maintain stations where examinations of vehicles to which these Regulations apply and the components of such vehicles may be carried out for the purposes of these Regulations and may provide and maintain the apparatus for carrying out such examinations.
16.-(1) A manufacturer of a type vehicle in respect of which a type approval certificate is in force shall keep a record of every certificate of conformity issued by him under Regulation 7 being a record of the serial number of the certificate and of the manufacturer's identification number assigned to the vehicle in respect of which the certificate was issued and of the Community reference numbers of the Community Directives or the Community Regulations with the requirements of which the vehicle conformed.
(2) A person authorised for the purpose by the Minister may, on giving any such manufacturer reasonable notice and after production, if so required, of his authority, require the manufacturer to produce for inspection the records kept by him under paragraph (1) and the authorised person may inspect and take copies of such records.
(3) In a case where any such manufacturer fails to comply with a requirement under paragraph (2) or obstructs an authorised person in the exercise of his powers under that paragraph, the Minister may treat the case as if there had been, in relation to the type approval certificate mentioned in paragraph (1), a breach of a condition such as is mentioned in Regulation 9(2) and (without prejudice to the application of Regulation 9(2) in respect of any other breach of a condition so mentioned) the provisions of that Regulation and of Regulations 13 and 14 shall apply accordingly in relation to that certificate.
Norman Fowler
Minister of Transport
6th August 1980
| 1 | 2 | 3 | ||
|---|---|---|---|---|
| Community Directive | ||||
| Item Number | Subject Matter | |||
| (a) | (b) | (c) | ||
| Reference Number | Date | Official Journal Reference | ||
| 1 | 70/157/EEC or 70/157/EEC as amended by 73/350/EEC or 70/157/EEC as amended by 73/350/EEC and by 77/212/EEC | 6 February 1970 7 November 1973 8 March 1977 | O.J. L42, 23.2.1970, p. 16 (S.E. 1970 (I), p. 111) O.J. L321, 22.11.1973, p. 33 O.J. L66, 12.3.1977, p. 33 | The permissible sound level and the exhaust system of motor vehicles |
| 2 | 70/220/EEC or 70/220/EEC as amended by 74/290/EEC or 70/220/EEC as amended by 74/290/EEC and by 77/102/EEC or 70/220/EEC as amended by 74/290/EEC and by 77/102/EEC and by 78/665/EEC | 20 March 1970 28 May 1974 30 November 1976 14 July 1978 | O.J. L76, 6.4.1970, p. 1 (S.E. 1970(I), p. 171) O.J. L159, 15.6.1974, p. 61 O.J. L32, 3.2.1977, p. 32 O.J. L223, 14.8.1978, p. 48 | Measures to be taken against air pollution by gases from positive ignition engines of motor vehicles |
| 3 | 70/221/EEC or 70/221/EEC as amended by 79/490/EEC | 20 March 1970 18 April 1979 | O.J. L76, 6.4.1970, p. 23 (S.E. 1970(I), p. 192) O.J. L128, 26.5.1979, p. 22 | Liquid fuel tanks and rear underrun protection for motor vehicles and their trailers |
| 4 | 70/222/EEC | 20 March 1970 | O.J. L76, 6.4.1970, p. 25 (S.E. 1970(I), p. 194) | The mounting and fixing of rear registration plates on motor vehicles and their trailers |
| 5 | 70/311/EEC | 8 June 1970 | O.J. L133, 18.6.1970, p. 10 (S.E. 1970(II), p. 375) | The steering equipment for motor vehicles and their trailers |
| 6 | 70/387/EEC | 27 July 1970 | O.J. L176, 10.8.1970, p. 5 (S.E. 1970(II), p. 564) | The doors of motor vehicles and their trailers |
| 7 | 70/388/EEC | 27 July 1970 | O.J. L176, 10.8.1970, p. 12 (S.E. 1970(II), p. 571) | Audible warning devices for motor vehicles |
| 8 | 71/127/EEC or 71/127/EEC as amended by 79/795/EEC | 1 March 1971 20 July 1979 | O.J. L68, 22.3.1971, p. 1 (S.E. 1971(I), p. 136) O.J. L239, 22.9.1979, p. 1 | The rear view mirrors of motor vehicles |
| 9 | 71/320/EEC or 71/320/EEC as amended by 74/132/EEC or 71/320/EEC as amended by 74/132/EEC and by 75/524/EEC or 71/320/EEC as amended by 74/132/EEC and by 75/524/EEC and by 79/489/EEC | 26 July 1971 11 February 1974 25 July 1975 18 April 1979 | O.J. L202, 6.9.1971, p. 37 (S.E. 1971(III), p. 746) O.J. L74, 19.3.1974, p. 7 O.J. L236, 8.9.1975, p. 3 O.J. L128, 26.5.1979, p. 12 | The braking devices of certain categories of motor vehicles and their trailers |
| 10 | 72/245/EEC | 20 June 1972 | O.J. L152, 6.7.1972, p. 15 (S.E. 1972(II), p. 637) | The suppression of radio interference produced by spark-ignition engines fitted to motor vehicles |
| 11 | 72/306/EEC | 2 August 1972 | O.J. L190, 20.8.1972, p. 1 (S.E. 1972(III), p. 889) | The emission of pollutants from diesel engines for use in vehicles |
| 12 | 74/60/EEC or 74/60/EEC as amended by 78/632/EEC | 17 December 1973 19 May 1978 | O.J. L38, 11.2.1974, p. 2 O.J. L206, 29.7.1978, p. 26 | The interior fittings of motor vehicles (interior parts of the passenger compartment other than the interior rear-view mirrors, layout of the controls, the roof, sliding roof or opening roof, the back rest and rear part of the seats) |
| 13 | 74/61/EEC | 17 December 1973 | O.J. L38, 11.2.1974, p. 22 | Devices to prevent the unauthorised use of motor vehicles |
| 14 | 74/297/EEC | 4 June 1974 | O.J. L165, 20.6.1974, p. 16 | The interior fittings of motor vehicles (the behaviour of the steering mechanism in the event of an impact) |
| 15 | 74/408/EEC | 22 July 1974 | O.J. L221, 12.8.1974, p. 1 | The interior fittings of motor vehicles (strength of seats and of their anchorages) |
| 16 | 74/483/EEC or 74/483/EEC as amended by 79/488/EEC | 17 September 1974 18 April 1979 | O.J. L266, 2.10.1974, p. 4 O.J. L128, 26.5.79, p. 1 | The external projections of motor vehicles |
| 17 | 75/443/EEC | 26 June 1975 | O.J. L196, 26.7.1975, p. 1 | Reverse and speedometer equipment of motor vehicles |
| 18 | 76/114/EEC or 76/114/EEC as amended by 78/507/EEC | 18 December 1975 19 May 1978 | O.J. L24, 30.1.1976, p. 1 O.J. L155, 13.6.1978, p. 31 | Statutory plates and inscriptions for motor vehicles and their trailers, and their location and method of attachment |
| 19 | 76/115/EEC | 18 December 1975 | O.J. L24, 30.1.1976, p. 6 | Anchorages for motor vehicle safety belts |
| 20 | 76/756/EEC or 76/756/EEC as amended by 80/233/EEC | 27 July 1976 21 November 1979 | O.J. L262, 27.9.1976, p. 1 O.J. L51, 25.2.1980, p. 8 | Installation of lighting and light signalling devices on motor vehicles and their trailers |
| 21 | 76/757/EEC | 27 July 1976 | O.J. L262, 27.9.1976, p. 32 | Reflex reflectors for motor vehicles and their trailers |
| 22 | 76/758/EEC | 27 July 1976 | O.J. L262, 27.9.1976, p. 54 | End-outline marker lamps, front position (side) lamps, rear position (side) lamps and stop lamps for motor vehicles and their trailers |
| 23 | 76/759/EEC | 27 July 1976 | O.J. L262, 27.9.1976, p. 71 | Direction indicator lamps for motor vehicles and their trailers |
| 24 | 76/760/EEC | 27 July 1976 | O.J. L262, 27.9.1976, p. 85 | Rear registration plate lamps for motor vehicles and their trailers |
| 25 | 76/761/EEC | 27 July 1976 | O.J. L262, 27.9.1976, p. 96 | Motor vehicle headlamps which function as main beam and/or dipped beam headlamps and incandescent electric filament lamps for such headlamps |
| 26 | 76/762/EEC | 27 July 1976 | O.J. L262, 27.9.1976, p. 122 | Front fog lamps for motor vehicles and filament lamps for such lamps |
| 27 | 77/389/EEC | 17 May 1977 | O.J. L145, 13.6.1977, p. 41 | Motor vehicle towing devices |
| 28 | 77/538/EEC | 28 June 1977 | O.J. L220, 29.8.1977, p. 60 | Rear fog lamps for motor vehicles and their trailers |
| 29 | 77/539/EEC | 28 June 1977 | O.J. L220, 29.8.1977, p. 72 | Reversing lamps for motor vehicles and their trailers |
| 30 | 77/540/EEC | 28 June 1977 | O.J. L220, 29.8.1977, p. 83 | Parking lamps for motor vehicles |
| 31 | 77/541/EEC | 28 June 1977 | O.J. L220, 29.8.1977, p. 95 | Safety belts and restraint systems of motor vehicles |
| 32 | 77/649/EEC | 27 September 1977 | O.J. L267, 19.10.1977, p. 1 | The field of vision of motor vehicle drivers |
| 33 | 78/316/EEC | 21 December 1977 | O.J. L81, 28.3.1978, p. 3 | Interior fittings of motor vehicles (identification of controls, tell-tales and indicators) |
| 34 | 78/317/EEC | 21 December 1977 | O.J. L81, 28.3.1978, p. 27 | Defrosting and demisting systems of glazed surfaces of motor vehicles |
| 35 | 78/318/EEC | 21 December 1977 | O.J. L81, 28.3.1978, p. 49 | Wiper and washer systems of motor vehicles |
| 36 | 78/548/EEC | 12 June 1978 | O.J. L168, 26.6.1978, p. 40 | Heating systems for the passenger compartment of motor vehicles |
| 37 | 78/549/EEC | 12 June 1978 | O.J. L168, 26.6.1978, p. 45 | Wheel guards of motor vehicles |
| 38 | 78/932/EEC | 16 October 1978 | O.J. L325, 20.11.78, p. 1 | Head restraints of seats of motor vehicles |
| Community Reference No. | Date | Official Journal Reference | Subject Matter |
|---|---|---|---|
| (EEC) No. 1463/70 | 20 July 1970 | O.J. L164, 27.7.1970, p. 1 (S.E. 1970(II), p. 482) | Recording equipment in road transport |
| as amended by 1787/73 | 25 June 1973 | O.J. L181, 4.7.1973, p. 1 | |
| and | |||
| as amended by 2828/77 | 12 December 1977 | O.J. L334, 24.12.1977, p. 5 |
| Title | Year and Number |
|---|---|
| The Motor Vehicles (Type Approval) Regulations 1973 | S.I. 1973/1199 |
| The Motor Vehicles (Type Approval) (Amendment) (No. 2) Regulations 1974 | S.I. 1974/763 |
| The Motor Vehicles (Type Approval) (Amendment) (No. 3) Regulations 1978 | S.I. 1978/1832 |
| The Motor Vehicles (Type Approval) (Amendment) Regulations 1979 | S.I. 1979/1089 |
1. These Regulations consolidate, with drafting and other amendments, the Motor Vehicles (Type Approval) Regulations 1973 and the other Regulations specified in Schedule 3.
2. The non-drafting amendments-
add rear-view mirrors which comply with the requirements of Council Directive 71/127/EEC as amended by Commission Directive 79/795/EEC to the number of vehicle parts which may be type-approved under the provisions of these Regulations;
add Commission Directive 80/233/EEC which amends Council Directive 76/756/EEC on the installation of lighting and light signalling devices on motor vehicles and their trailers; and
omit misconceived provisions relating to the suspension of type approval certificates where vehicles or vehicle components having a certificate of conformity are altered.
3. These Regulations provide, in accordance with Council Directive 70/156/EEC of 6 February 1970, for the type approval of motor vehicles and trailers specified in Regulation 4. Regulation 5 provides that where the Minister is satisfied on an application made to him under Regulation 6 that a vehicle or, as the case may be, vehicle component conforms with certain information and the type approval requirements and that adequate arrangements have been made for conformity of production he shall approve the vehicle as a type vehicle or, as the case may be, the vehicle component as a type vehicle component and shall issue a type approval certificate accordingly. Regulation 5 also makes provisions against the events of the Minister being satisfied that one or more, but not all, of the type approval requirements are satisfied, or deciding not to issue a type approval certificate.
4. Part III of the Regulations contains general provisions as to application (Regulation 6), certificates of conformity (Regulation 7), marking (Regulation 8), conditions of issue, cancellation and suspension of type approval certificates (Regulation 9), notifications by manufacturers as to cessation or alteration of production (Regulation 10), cancellations, suspensions or modifications of type approval certificates (Regulations 11 and 12), notices relating to such cancellations, suspensions or modifications (Regulation 13) and appeals (Regulation 14).
5. Part IV of the Regulations contains provisions as to testing stations (Regulation 15) and records (Regulation 16).
6. Schedule 1 prescribes certain forms, and Schedule 2 specifies (in conjunction with the definitions in Regulation 3 of "the type approval requirements", "the Community Directives" and "the Community Regulations") the type approval requirements.
S.I. 1972/1811.
